How to Stain a Fence
STEP 1: Choose the right day (or days) for your project.
Before staining a wood fence, scan the weekly weather forecast and select a day with temperatures between 50 and 80 degrees, broken to moderate humidity, and no precipitation expected for the adjacent 24 hours. If you ’ re discouraged by the prospects, remember that “ good things come to those who wait ”. Extreme cold or moisture can prolong the dry meter of wood stain, while the reverse extreme can dry out stain excessively cursorily and leave behind unwanted lap marks on the argue.
Reading: How To: Stain a Fence
STEP 2: Prepare the wood for painting.
Depending on the stream condition of your fence, you may need to strip or sand the airfoil .
Starting with a previously stained or finished fence?
Apply wood mark or finish stripper to the slats according to the manufacturer ’ sulfur instructions, then scrub the slats with a stiff-bristle brush to loosen the old varnish and slough off upright wood fibers .
Learning how to stain a fence that is new?
see the stain will penetrate the wood with the water test : lightly spray a small section of the fence with a garden hose. If water beads form on the slats, lightly sand the slats in the direction of the wood grain. Water successfully penetrating the slats, though, indicates that your wooden fence can readily absorb the stain .
STEP 3: Clean the fence thoroughly and let dry.
Clean the fence with water from a hard-hitting spray nozzle attached to a garden hose ( or use a might washer ). This will remove light to moderate dirt accumulations and complete the job of the wood stain stripper in blasting away any old varnish from the fence, if applicable. If using a office washer, choose for a low-powered unit operating at no more than 2,000 psi so as not to weather the wood slats. Make indisputable to let the forest dry out wholly before continuing. Get a professional to do it for you Receive loose, no-commitment estimates from pro painters near you .Find local pros +
STEP 4: Spot-treat mold or mildew with diluted bleach.
If you spot model or mildew deposits on the fence, prepare a solution of bleach diluted with water in a bucket. Donning rubber gloves, apply the bleach to the slats with a garden sprayer, allowing it to settle into the slats for a few minutes before rinsing the fence clean with a hard-hitting spray beak or power washer. Again, make certain to let the wood dry out wholly before continuing.
Read more : Smoked Pork Shoulder
STEP 5: Use wood filler to patch imperfections in the fence slats.
Repair chips, gouges, or cracks in the fence with woodwind makeweight. If needed, replace damaged slats .
STEP 7: Protect nearby plants and parts of the fence not to be stained.
Use cougar ’ mho magnetic tape to protect areas of the fence you do not want to stain. similarly, protect surrounding vegetation at the infantry of the fence by covering it with drop cloths .
STEP 8: Proceed to applying stain to the fence slats.
Enlist a brush, curler, or atomizer to stain the slats .
- A natural-bristle brush is the best way to encourage oil-based
wood stain to permeate wooden fence slats. Dip the tip of the brush into a can of stain, then coat any horizontal slats of the fence from left to right. Afterwards, work your way from top to bottom down the entire length of each vertical slat, maintaining a wet tip at all times. Stain one to two slats at a time to prevent lap marks from forming. One you reach the bottom of a slat, stain the end grain.
- If using a roller, opt for a medium nap roller cover, then fully saturate the nap with the stain. Apply the stain in two- to three-foot sections of the fence at a time, taking care to back-brush, or re-paint over uncovered areas left by the previous stroke, with a wide brush. This will allow the stain to enter hard-to- reach grooves and recesses, and ensure an even coat free of lap marks.
- If using a sprayer, follow the same approach as for how to stain a fence with a roller, but stand back a comfortable distance from the fence to apply color.
STEP 9: Let the stain dry, then apply additional coats as desired.
When the entire fence has been stained, let it dry according to the stain manufacturer ’ second instructions. Apply extra coats of stain as needed to achieve the coveted depth of color. A single coating should be sufficient for a new wood argue or one that you besides plan to seal. ad
STEP 10: Finish the job with a coat of sealer.
While a good quality stain alone is sufficient to protect your fence from everyday wear-and-tear, applying a durable sealant over the tarnish can prolong the finish—and the life of your fence. For best results, apply a single coat of clear up, weatherproof sealant by brush, roller, or atomizer. cursorily back-brush unsealed grooves and recesses with a broad brush to achieve a uniform appearance. Allow the sealant to dry wholly .
STEP 11: Clean up!
Dispose of soiled drop cloths, remove the cougar ’ randomness magnetic tape from the slats, and reveal your like-new fence ! Go ahead and take the following couple of summers off—you earned it. only note that while translucent stains can concluding anywhere between two to five years, extreme point temperatures and haste can prematurely age the finish. Don ’ t lie on your laurels besides long and risk the weather damage : calculate to stain your fence every two to three years to preserve its shininess and weather protective qualities.
Read more : How to change your Instagram username
Get a professional to do it for you Receive free, no-commitment estimates from pro painters near you .Find local pros +