How to Stretch Carpet

One of the great things about wall-to-wall carpet is that its surface is completely politic and wrinkle-free. If you ’ ve ever watched rug being installed, you know that it didn ’ thyroxine get flat on its own–the installers had to wrestle it into its state of peace with especial stretch tools .

Carpet Stretching Tools

The two independent tools are the competently named might stretcher and the stifle kicker. Both have flat, aluminum heads that are fitted with rows of adjustable steel teeth, angled forward so they can better bite into the carpet .

Knee Kicker

A stifle kicker is about 20 inches long, with a square toothy head on one end and an equally-sized knee slog at the opposite end .

Power Stretcher

A exponent stretcher has a larger rectangular head, normally about 15 inches wide, that ’ s connected by a spring-loaded lever to a series of telescoping tubes that terminate in a slog block.

Depending on the model, the tubes can be extended up to about 40 feet in length so that the capstone can bear against the antonym wall. A good-quality kicker costs less than $ 100, but ability stretchers start at around $ 500. so unless you ’ re going into the carpet clientele, it makes smell to rent, rather than buy. here ’ s how to use them :
Related

How to Repair Loose Carpet

Steps for Stretching Carpet

When you ’ re installing newly carpet, the first thing you ’ ll want to do is nail down tack strips around the margin of the board .
Tack strips resemble antique wooden yardsticks pre-nailed with belittled, very sharp pins. These strips bite into the carpet and keep it in stead.

Leave a space of a copulate of inches between the leach and the wall. Install the carpet diggings, which should cover the shock within the boundary established by the baste strips. Use a hammer staple gun to staple down the pad, then you can roll out the carpet .
The first carpet stretching creature you ’ ll use is the stifle kicker .

  1. First, check the depth of the teeth—when the head is pressed down on the carpet, the teeth should bite into the pile and backing, but not protrude through it. You can use the dial on the kicker’s head to adjust the depth of the teeth.
  2. Starting in one corner, press the kicker head firmly into the carpet a few inches away from the tack strip, and use your knee to strike the kicker’s padded end.
  3. Maintain pressure on the kicker and press the edge of the carpet down onto the tack strip, making sure to leave some excess carpet against the wall that you can later trim at the baseboard.
  4. Repeat these steps along the same wall until the carpet is taut.
  5. With the carpet in place along the first wall, assemble and adjust the power stretcher so that its head is a few inches opposite from the first wall and the padded tail block is placed against the first wall’s baseboard.
  6. Press the head’s teeth into the carpet, again checking that the teeth are adjusted to the correct length.
  7. Now engage the mechanism by pulling back on the level, which will push the carpet toward the second wall. Keep an eye on the lever’s adjustable tension; too much tension can damage the carpet and not enough will leave slack.
  8. Press the carpet down into the tack strip to lock it in place and move the assembly to the next section of carpet.
  9. When the carpet is stretched toward the second wall, use the knee kicker to attach the carpet on the next perpendicular wall and stretch it to the final wall with the power stretcher.
  10. Once the carpeting has been successfully stretched across the room, use a curved carpet knife or sharp utility knife to trim the edges.
  11. Using one hand to press the carpet down into the intersection of the baseboard and floor, cut away the excess with the knife. If your rental center has one, you can use a specialized carpet edging tool instead of a knife to make clean cuts against the baseboard. At this point, it’s handy to have a stair tool, which has a heavy, wide steel blade. Installers use stair tools to wedge the trimmed carpet down into the crevice between the tack strip and the baseboard.

Put New Life into Older Carpets

These lapp extend tools can be used to work their magic on older wall-to-wall carpet that has developed loose spots and ripples .

  • Start by peeling the carpet from the perimeter tack strips. If the tack strips are rotting due to water damage or have lost their grip because they’ve been pounded down from foot traffic, it may be necessary to replace them with new strips.
  • Roll the carpet back into place, and, using a knee kicker, lock down the carpet along the first wall, then continue the process with the power stretcher.
source : https://thaitrungkien.com
Category : Tutorial

Trả lời

Email của bạn sẽ không được hiển thị công khai.